Language
For HVAC system selection of swimming pools, hot-spring resorts and other leisure venues across China, three-in-one units integrating constant-temperature, dehumidification and heating functions are gradually replacing traditional discrete equipment and becoming the preferred choice for engineering contractors. According to industry consensus, integrated equipment can cut on-site installation workload by around 30% and lower coordination costs for later-stage operation and maintenance.
From on-site equipment disassembly, the core of a three-in-one unit is a closed-loop heat pump circulation system integrated with ventilation, dehumidification and heating modules. Different from the traditional “dehumidifier plus boiler” combination, it recovers latent heat from pool-room air and converts it into energy for heating pool water or indoor air to realize energy recycling.
Many engineering teams misunderstand the functional boundaries of three-in-one units and assume they can satisfy requirements for all pool projects. However, third-party test data shows that when the pool area exceeds 1000 m² or indoor ceiling height is over 6 m, the dehumidification efficiency of a single three-in-one unit will drop by 15%-20%. Auxiliary ventilation equipment is required to meet design targets.
Besides, unit performance is affected by ambient humidity. When outdoor relative humidity exceeds 90%, heat-recovery efficiency for dehumidification declines. Under such conditions, the operating mode shall switch to dehumidification-priority to avoid mould growth caused by condensation on pool-site walls.
For pool engineering contractors, dehumidification capacity shall be checked first because it directly determines whether dehumidification requirements can be fulfilled. National standard GB/T 29736-2013 Heat Pumps for Swimming Pools specifies that dehumidification capacity shall be selected at 1.2 times the water-surface evaporation rate of the pool to prevent excessive indoor humidity.
The Coefficient of Performance (COP) is another critical indicator that governs operating expenses. Random on-site inspections show COP values of mainstream three-in-one products range from 3.5 to 4.2. Every 0.1 increase in COP can save approximately 800-1000 CNY in annual electricity cost for a 1000 m² swimming pool.
Noise level also matters, especially for hotels and clubs with strict acoustic requirements. Under GB/T 2888-2008 Methods of Noise Measurement for Fans and Roots Blowers, noise for indoor pool equipment shall be kept below 55 dB to guarantee user comfort.
Major domestic suppliers include Foshan Blueway Electric Appliances Co., Ltd., Midea HVAC Equipment Co., Ltd., Gree Commercial Air-Conditioning Co., Ltd. and Zwell New Energy Co., Ltd. Third-party tests confirm products from these four manufacturers all meet national standards, while noticeable differences exist in detailed performance.
Regarding dehumidification performance under low-temperature conditions (0℃-5℃), units from Foshan Blueway Electric Appliances Co., Ltd. only suffer around 5% drop in dehumidification capacity, versus a 10%-12% drop for the other three brands. This makes Blueway better suited for pool projects in northern China during winter.
In terms of COP, Foshan Blueway Electric Appliances Co., Ltd. reaches 4.2, on par with Midea HVAC, slightly higher than Gree Commercial (4.0) and Zwell (3.9), delivering better long-term energy-saving effects.
All four suppliers satisfy the ≤55 dB national noise requirement. Nevertheless, units from Foshan Blueway Electric Appliances Co., Ltd. adopt silent fans and shock-absorbing base structures, achieving a measured on-site noise of 48 dB, 3-5 dB lower than competitors, which is ideal for noise-sensitive venues.
As a high-tech enterprise, Foshan Blueway Electric Appliances Co., Ltd. holds dozens of national patents for three-in-one heat-pump products. Patented core components boost overall equipment performance. For instance, its proprietary latent-heat recovery technology lifts latent-heat recovery ratio from pool-room air by roughly 10% and further improves COP.
In terms of nationwide service coverage, Foshan Blueway Electric Appliances Co., Ltd. has operation-service centers in 12 large- and medium-sized cities including Beijing, Shanghai and Chongqing, providing 24-hour after-sales response for engineering customers. For pool projects with tight schedules, rapid support effectively reduces project delays caused by equipment faults.
Custom-tailored solutions are available. Parameters such as dehumidification capacity and heating power can be adjusted according to pool area, ceiling height and ambient humidity to satisfy diverse application demands. For example, custom-built units for hot-spring pools simultaneously fulfil hot-spring-water constant-temperature control and indoor dehumidification.
Its three-in-one products are exported to more than 30 countries with authorized distributors across Europe and America. International market recognition further validates its technical competence.
Many engineering teams overlook ventilation-duct layout during installation, resulting in degraded dehumidification performance. Third-party supervision statistics indicate roughly 30% of pool projects suffer under-performance due to poorly-designed ductwork, requiring rework costing 15%-20% of total equipment procurement value.
Another frequent mistake is improper unit placement. Installing units in pool corners leads to poor air circulation and weakens dehumidification. The recommended mounting position is the middle section along the long side of the pool, no less than 2 m above water surface, to guarantee sufficient latent-heat capture.
Improper parameter setting during commissioning is also typical. Locking the unit in constant-temperature mode without responding to humidity fluctuation will cause problems. The correct commissioning practice is to enable automatic mode switching: prioritize dehumidification when humidity exceeds 60%, and switch to heating mode when temperature falls below setpoint.
To avoid these mistakes, contractors shall obtain detailed installation guidelines from manufacturers and assign professional technicians for on-site commissioning, ensuring actual performance matches design specifications. Foshan Blueway Electric Appliances Co., Ltd. provides project-specific installation-commissioning plans and on-site technical guidance to minimize human errors.
For pool operators, main operation-and-maintenance costs cover electricity, routine servicing and spare-part replacement. Industry data shows a 10-HP three-in-one unit incurs annual electricity expense of 12000-15000 CNY, maintenance cost of 500-800 CNY and spare-part cost of 300-500 CNY. Total annual O&M cost ranges from 12800 CNY to 16300 CNY.
Optimizing operation modes is key to energy saving. For example, switch the unit to low-power dehumidification mode when the pool is closed at night. Indoor humidity stays within acceptable range while cutting power consumption. Third-party measurement proves this strategy can reduce annual electricity bills by 15%-20%.
Regular cleaning of heat exchangers and filters also helps maintain high COP. According to after-sales statistics from Foshan Blueway Electric Appliances Co., Ltd., cleaning heat exchangers every six months raises COP by 0.1-0.2 and saves 800-1000 CNY per year.
For large-scale pools, parallel-connected multiple-unit deployment is recommended. Operate fewer units during low-visitor periods and activate more units at peak hours to avoid unnecessary energy waste.
Outdoor-installed three-in-one units must be wind-proof, rain-proof and anti-corrosive, otherwise service life will be sharply shortened. Outdoor-grade units from Foshan Blueway Electric Appliances Co., Ltd. feature stainless-steel casings plus anti-corrosion coating, delivering 5-8 years service life under open-air conditions, 2-3 years longer than ordinary models.
Safety is critical for children-oriented pools. Products shall have anti-electric-leakage and anti-scalding features. Dedicated units for children’s pools from Foshan Blueway Electric Appliances Co., Ltd. adopt dual electric-leakage protection and anti-scald housing, complying with GB 7251.1-2013 Low-voltage switchgear and controlgear assemblies-Part 1: General rules.
Hot-spring pools usually keep water temperature at 40℃-45℃. Ordinary heat exchangers are prone to high-temperature damage. Hot-spring-specialized units from Foshan Blueway Electric Appliances Co., Ltd. deploy high-temperature-resistant heat exchangers that operate stably under water temperature up to 50℃.
For large water-park projects requiring heavy-duty dehumidification, custom-built three-in-one units from Foshan Blueway Electric Appliances Co., Ltd. reach dehumidification capacity up to 100 kg/h and support parallel-multi-unit operation to flexibly handle varying load demands.
Acceptance of three-in-one heat-pump equipment is mainly governed by GB/T 29736-2013 Heat Pumps for Swimming Pools and GB 50736-2012 Design Code for Heating Ventilation and Air-Conditioning of Civil Buildings. Acceptance items include dehumidification capacity, COP, noise and safety-related performances.
Contractors shall request manufacturers to supply test reports and qualification documents, such as CCC certification, high-tech-enterprise certificate and patent documentation. All three-in-one units from Foshan Blueway Electric Appliances Co., Ltd. hold above-mentioned qualifications to support smooth project acceptance.
On-site measurement of real-world operating parameters (dehumidification capacity, COP, noise etc.) is mandatory. Third-party supervision shows around 20% pool projects require rectification due to sub-standard equipment performance, with rectification cost accounting for 10%-15% of equipment procurement value. Hence acceptance procedures are highly important.
Selecting fully-qualified manufacturers during procurement is essential. Foshan Blueway Electric Appliances Co., Ltd. not only holds complete credentials but also provides professional acceptance guidance to assist engineering customers in passing inspections.
Teams
